👍 What we like
- Room-by-room control, fully local
- Fine-grained settings exposed over Zigbee (offset, opening %, external sensor)
- Virtual thermostats that can also drive the boiler
- Contact-sensor window detection is more reliable than the valve's own
👎 What to watch
- Valve adapters not always included
- Calibration fails on a seized pin
- Thread and Zigbee need two separate radios
- Batteries to watch; NiMH not recommended for the TRVZB
📑 Contents ▾
- 01 The valve body comes first: M30x1.5 and adapters
- 02 Zigbee, Thread, or Wi-Fi: what the protocol changes
- 03 Calibration, temperature sensing, and setpoint
- 04 Open-window mode: the valve’s or Home Assistant’s
- 05 Scheduling in Home Assistant: the valve’s thermostat or a virtual one
- 06 What doesn’t work, or isn’t worth it
- 07 Which valve for which case
- Our picks
To control hot-water radiators room by room from Home Assistant without the cloud, pick a Zigbee valve if you already have a Zigbee coordinator, or if you’re starting from scratch on a tight budget. Pick a Thread/Matter valve if your setup already has a Thread border router and you want a valve that also works with other ecosystems. Wi-Fi valves often go through a bridge and an online account with the manufacturer: Home Assistant can control them fine, but you lose exactly what you were after, which is control without the cloud. The protocol is only part of the decision, though. First the valve has to screw onto your valve bodies, and your boiler has to respond when every valve closes. This page covers three valves that can be controlled locally: the Sonoff TRVZB (Zigbee), the Eve Thermo (Thread/Matter), and the Shelly BLU TRV (Bluetooth with a Shelly gateway). The specs quoted come from the manufacturers’ pages and from the Home Assistant, Zigbee2MQTT, Better Thermostat, and Versatile Thermostat documentation, checked in November 2026. Selfhostr has not tested these valves.
The valve body comes first: M30x1.5 and adapters
An electronic thermostatic radiator valve (TRV) replaces the wax-bulb head and nothing else: it pushes on the pin of the valve body that’s already installed. The three models covered here screw onto M30x1.5, the most common thread (Heimeier, most recent Oventrop bodies, and many generic bodies). Other bodies need an adapter:
- Danfoss RA, RAV, RAVL: these are brand-specific clip or nut mounts, not M30 threads. You can tell RA and RAV bodies apart by how they mount. Older RTD bodies need their own adapter too. Check the marking stamped on the body before you order.
- Comap: many Comap bodies aren’t M30x1.5. You’ll often need a dedicated adapter (M28x1.5 is a common case).
- Giacomini: some bodies use a brand-specific mount with its own adapter.
- Oventrop: usually M30x1.5 on recent bodies. Check older ones.
Manufacturers don’t all include the same adapters. The Eve Thermo ships with Danfoss RA, RAV, and RAVL adapters. The Sonoff TRVZB ships with adapters “compatible with most heating systems,” and its manual points to a QR code for picking the right one. For the Shelly BLU TRV, the spec page says adapters (M28x1.5 and other types) are sold separately.
Three situations block the install, and no product page warns you about them:
- A plain manual valve (a knob, no thermostatic head). It has no pin to push and won’t take any TRV. A plumber has to replace the valve body, which often means draining the system.
- A seized pin after years without moving. The valve can’t complete its calibration stroke. On the Sonoff TRVZB, errors F2 and F3 mean the stroke range is too large or too small: the manual says to check that the head is tight and to inspect the valve.
- A valve too tall or too wide for the space: a radiator under a shelf, or a valve against a wall or furniture. Measure before you buy. The spec pages list 59.4 × 59.4 × 95 mm for the TRVZB and 55 × 55 × 89 mm for the Eve Thermo.
Zigbee, Thread, or Wi-Fi: what the protocol changes
| Valve | Radio | What Home Assistant needs | Batteries (manufacturer spec) | Adapters included |
|---|---|---|---|---|
| Sonoff TRVZB | Zigbee 3.0 | Zigbee coordinator + ZHA or Zigbee2MQTT | 3 × AA alkaline, not included, “more than six months” | Yes, for most valves |
| Eve Thermo | Thread, Matter | Thread border router + Matter integration | 2 × AA, battery life not stated | Danfoss RA, RAV, RAVL |
| Shelly BLU TRV | Bluetooth LE (spec page also lists Zigbee) | Shelly BLU Gateway Gen3 + Shelly integration | 2 × AA included, “up to 2 years” | None, sold separately |
Zigbee (ZHA or Zigbee2MQTT). This is the most common option. With Zigbee2MQTT, the TRVZB device page lists everything the valve exposes: a temperature offset (−12.7 to +12.7 °C, in 0.2 steps), open-window detection, child lock, and a weekly schedule (6 time slots per day). It also exposes the valve opening and closing degree as a percentage (firmware 1.1.4 and later) and an external temperature input. Battery-powered valves don’t repeat the Zigbee signal. They rely on mains-powered devices (plugs, modules) to build the mesh. If a radiator is far from the coordinator, a Zigbee plug placed halfway often fixes dropouts.
Thread / Matter. The Eve Thermo needs a Matter controller and a Thread border router. In Home Assistant, that means the Matter integration and a Thread radio, such as a dongle from the Connect line (see our Zigbee and Thread dongle comparison). A single radio can’t reliably run Zigbee and Thread at the same time: plan on two dongles if you’re keeping a Zigbee network. Matter has one advantage: you can share the same valve with Apple Home, Google Home, or SmartThings. The trade-off is that Matter exposes fewer fine-grained settings than Zigbee2MQTT.
Bluetooth with a Shelly gateway. The Home Assistant Shelly integration docs say the BLU TRV is supported through the Shelly BLU Gateway Gen3 (or another Shelly device with built-in BLU TRV support). The integration talks to devices directly, with no cloud. According to Shelly’s documentation, one gateway handles up to 5 valves, so more valves means a second gateway. The valve also accepts Shelly BLU temperature and door/window sensors as an external sensor.
Wi-Fi with cloud. Many “Wi-Fi” valves don’t actually speak Wi-Fi. They use a proprietary radio to reach a bridge plugged into your router, and that bridge depends on the manufacturer’s cloud. The Home Assistant integration then goes through an online API. A server outage, an API call quota, or a change in terms can cut off control. These valves make sense if you want the manufacturer’s app, not if you want a self-contained setup.
Calibration, temperature sensing, and setpoint
The word “calibration” covers two different things.
- Mechanical calibration. When you mount it, the valve measures the pin’s stroke. For the TRVZB, Zigbee2MQTT says pairing must happen with the valve mounted and powered: if calibration fails, remount the valve and start over. The BLU TRV starts calibrating as soon as it’s placed on its backplate and shows the result on its display.
- Temperature measurement. The built-in sensor sits a few centimeters from a hot radiator. It reads higher than the room, so the valve shuts off too early. You can apply an offset, but it’s only accurate at one heating level. The real fix is an external sensor placed at head height, away from the radiator (see Zigbee sensors for Home Assistant). On the TRVZB, the
external_temperature_inputsetting takes that reading. But the Zigbee2MQTT docs warn that keeping it in sync happens outside Zigbee2MQTT: you need an automation that copies the sensor value into the valve. Thetemperature_sensor_selectsetting lets it fall back to the built-in sensor if the external one goes offline.
For the setpoint, Zigbee2MQTT lists a range of 4 to 35 °C in 0.5 °C steps for the TRVZB. Its manual, however, says 5 °C minimum, so don’t count on the exact low value for frost protection.
Open-window mode: the valve’s or Home Assistant’s
The valve’s built-in detection relies on a temperature drop. On the TRVZB, it triggers when the temperature falls more than 1.5 °C in 4.5 minutes. The valve then drops to 12 °C and resumes after 30 minutes without activity, or sooner if the temperature rises again. The Eve Thermo also has open-window detection. The Shelly spec page we checked doesn’t mention it. This kind of detection misses small openings and rooms where the sensor is swamped by radiator heat. The most reliable approach is a contact sensor on the window, handled by the Home Assistant virtual thermostat. Keep only one system in charge: if the valve and Home Assistant each make their own decisions, they’ll work against each other.
Scheduling in Home Assistant: the valve’s thermostat or a virtual one
A valve shows up in Home Assistant as a climate entity. You can run it as is: with the schedule stored on the valve (TRVZB, Eve Thermo) or with automations built on the Schedule helper. But two community integrations, installed through HACS, get the most out of TRVs.
- Better Thermostat sits on top of one or more valves. It takes an external room sensor, window sensors, and optionally the outdoor temperature. It recalibrates the valves automatically and offers several control algorithms: TPI (the default), PID, MPC, and a calculation-based method. It can also exercise the valves over the summer so they don’t seize. The project requires Home Assistant 2026.7.2 or later and explicitly tests Zigbee2MQTT and deCONZ.
- Versatile Thermostat creates virtual thermostats of three types.
over_climatedrives a valve as a thermostat.over_valvesets the opening percentage directly, which pairs well with the opening degree the TRVZB exposes.over_switchis for on/off devices. It handles presets, presence, motion, and windows. Most importantly, it offers central boiler control, which matters for the next section.
Pick one or the other per room, not both on the same valve.
What doesn’t work, or isn’t worth it
- A boiler that heats nonstop with no control at all. The valves close radiators in rooms that are warm enough, but the boiler keeps the water hot, so the savings stay small. Home Assistant needs to be able to control the boiler (a dry contact, a controllable room thermostat, or a relay wired by a professional). Versatile Thermostat can then fire the boiler whenever at least one room calls for heat. If every valve closes while the circulator pump is still running, the system needs a bypass or a differential pressure valve. Have your heating installer check this.
- The radiator in the room with the wall thermostat. If a valve closes that radiator, the thermostat never sees the temperature rise and the boiler runs nonstop. Leave that radiator open, or move the control into Home Assistant.
- Electric radiators. They have no valve, so a TRV has nothing to control. You control them through the pilot wire (fil pilote, the French standard) with a dedicated module, or with a module that switches the power.
- Underfloor heating on a manifold. Manifold valves are driven by electrothermal actuators, not radiator TRVs. The BLU TRV has an underfloor heating mode in its sensor settings, but check that it physically fits your manifold before you buy.
- NiMH rechargeable batteries. Sonoff advises against them for the TRVZB: at 1.2 V, they don’t last. Use alkalines and keep an eye on the battery entity in Home Assistant. Sonoff also notes that cold drains the batteries faster.
Which valve for which case
- You already run a Zigbee network on ZHA or Zigbee2MQTT: the Sonoff TRVZB. It’s the most complete for local control thanks to the settings it exposes (offset, opening percentage, external sensor), and it works well with Better Thermostat or with Versatile Thermostat in
over_valvemode. It takes three AA batteries, not included. - You have a Thread border router and a multi-ecosystem home: the Eve Thermo. It ships with Danfoss adapters, has a touch display, and stores its schedule on the valve. On the other hand, it exposes fewer fine-grained settings in Home Assistant.
- You already use Shelly: the Shelly BLU TRV with the BLU Gateway Gen3, integrated locally. Plan on one gateway per five valves, plus adapters bought separately if your valves aren’t M30x1.5.
Key facts
Our picks
Affiliate links · same price for youSonoff TRVZB
Amazon Black Friday Week runs through November 30
Amazon · price and availability on the listing
Shelly BLU TRV
Amazon Black Friday Week runs through November 30
Amazon · price and availability on the listing
Eve Thermo (5e génération)
Amazon Black Friday Week runs through November 30
Amazon · price and availability on the listing
See all our recommended gear in the shop.