Comparisons 9 min read

Shelly modules for roller shutters and lighting: which ones to choose for Home Assistant?

Shelly 2PM Gen4 for shutters, 1PM Gen4 for lights, Dimmer Gen3 without neutral: wiring, calibration, Zigbee mode, wall-box space, and safety for Home Assistant.

S By Selfhostr · no sponsored content
Shelly modules for roller shutters and lighting: which ones to choose for Home Assistant?
This article may contain affiliate links (no extra cost to you, it funds the site). As an Amazon Associate, Selfhostr earns from qualifying purchases. See the disclosure.

👍 What we like

  • Existing wall switches stay in place and work without the network
  • Fully local control in Home Assistant, no cloud account
  • Per-channel power metering on Gen4 models
  • Gen4 modules work over Wi-Fi, Matter, or Zigbee

👎 What to watch

  • A 40 mm box is often too tight with the switch mechanism
  • Without neutral: ceiling bypass below 20 W and no metering
  • Shutters with factory radio control can't be driven
  • No firmware updates in Zigbee mode
📑 Contents ▾

Want to control your roller shutters and lights from Home Assistant while keeping your existing wall switches? A Shelly module tucked into the wall box behind the switch does the job. The switches stay in place and keep working even when the network is down. Your choice comes down to three questions. Wired roller shutters: the Shelly 2PM Gen4 in cover mode (the “Cover” profile). A simple light with neutral in the box: the Shelly 1PM Gen4, which also measures consumption. No neutral behind the switch, or you want dimming: the Shelly Dimmer Gen3, which works without neutral. All three integrate locally with Home Assistant, with no cloud. The two Gen4 models can also switch to Zigbee, with trade-offs you should know before going that route. If your electrical panel is recent and you’re rewiring, the Pro range (DIN rail) becomes a serious alternative.

The specifications cited here come from Shelly’s official knowledge base, the Home Assistant and Zigbee2MQTT documentation, and Legrand, as checked in November 2026. Selfhostr has not tested these modules: this page covers what the manufacturers say and what that means at install time.

Three modules, three wiring situations

Shelly 2PM Gen4Shelly 1PM Gen4Shelly Dimmer Gen3
Main useRoller shutter or 2 circuits1 circuit (lighting, ventilation…)Light dimming
NeutralN terminal provided, AC diagram uses neutralRequiredOptional
Current / load10 A per channel, 16 A total16 A150 W dimmable LED, 200 W total
Power meteringYes, per channelYesYes, only with neutral
RadioWi-Fi 6, Bluetooth 5.0, Zigbee, MatterWi-Fi 6, Bluetooth 5.0, Zigbee, MatterWi-Fi b/g/n, Bluetooth 4.2
Dimensions37 × 42 × 16 mm37 × 42 × 16 mm38 × 42.5 × 16.5 mm

All three take up roughly 4 × 4 × 1.6 cm. The trouble rarely comes from the module itself. It comes from the wires already in the box.

Roller shutters: the 2PM Gen4 in cover mode and calibration

The Shelly 2PM Gen4 replaces the up/down rocker of a wired shutter. It connects to the motor’s two control wires (up and down), the common, and neutral. The double wall switch connects to the module’s two inputs. Shelly lists roller shutters, blinds, and Venetian blinds, with slat tilt for the latter. The module also accepts a 24 V DC supply, but a typical European shutter is wired at 230 V.

What trips people up in practice:

  • The motor needs set limit switches. Shelly recommends using only motors with electronic or mechanical limit switches, and says they must be set before the device is connected. The module is no substitute for an end stop.
  • Calibration is what enables percentage positions. Once the Cover profile is selected, the module times a full travel. That’s what lets you ask for “40%” from Home Assistant later. The Home Assistant Shelly integration docs spell out the order: Cover profile, calibration, then slat settings if the blind has them. Recalibrate after any work on the motor or limit switches.
  • Radio shutters don’t apply. A motor with factory radio control (a remote, no separate up and down wires) often has only live, neutral, and ground: there’s no wired command for the module to drive. Count the conductors coming out of the shutter box before you buy.
  • One module per motor. Wiring two motors in parallel on the same output lets their limit switches feed back into each other: avoid it unless you use an isolation relay designed for that.
  • Obstacle detection exists on the 2PM Gen4. It relies on power metering and does not replace a mechanical safety device on a motorized shutter that children can reach.

In switch mode, the same module drives two independent circuits, for example both gangs of a double switch. In that case, stay within 10 A per channel and 16 A total.

Lighting with neutral: the 1PM Gen4

The Shelly 1PM Gen4 is the simple choice for a light fixture: a 16 A relay, voltage, current, and power metering, and your wall switch kept on the SW input. Its spec sheet is explicit: neutral is required. Its own consumption is listed as under 1 W.

Power metering is more useful than it sounds. It lets you check whether a bulb has burned out, track a ventilation unit or water heater switched by the relay, or feed Home Assistant’s Energy dashboard (see our guide to measuring power consumption). If you have no use for it, a dry-contact module without metering is enough, for example to trigger a gate or a boiler through a potential-free contact.

For push buttons that don’t switch any load (triggering a scene, controlling a group of Zigbee lamps), Shelly makes four-input modules with no relay at all: no point paying for a relay you’ll never use.

No neutral, or dimming: the Dimmer Gen3

In many older homes, the switch box only gets live and the switched return to the lamp. Neutral stays at the ceiling. The Shelly Dimmer Gen3 works in that setup, with limits its spec sheet spells out:

  • 20 W minimum load without neutral. Below that, which covers most LED ceiling fixtures, you need a bypass wired in parallel with the fixture, which means at the ceiling. The bypass also stops LEDs from glowing or flickering when off.
  • No power metering without neutral, and the protections (overpower, overvoltage, undervoltage) only work with neutral.
  • Trailing-edge dimming, up to 150 W of dimmable LED and 200 W total. Bulbs must be rated dimmable. Shelly recommends using the same model and brand on any one circuit.
  • 230 V and 50 Hz only, with 2.4 GHz Wi-Fi (b/g/n) and no Zigbee.

If you only need on/off without neutral, Shelly also makes a dedicated switch that comes with its own bypass. But if you can run a neutral to the box, do it: you get metering, reliable protections, and the option of the 1PM.

Local Wi-Fi, Matter, or Zigbee: what the radio mode changes

On Wi-Fi, Home Assistant’s Shelly integration is classified as “Local Push.” Gen2 and newer modules talk directly to Home Assistant over RPC, with no cloud and no special setup. Mains-powered modules can also act as Bluetooth proxies for BLE sensors, with passive or active listening but no GATT connections. Two precautions: give each module a static IP or a DHCP reservation, and consider a separate network for home automation (see VLANs to isolate home automation). If you put your Shellys on a VLAN, make sure Home Assistant can reach them.

Matter is the out-of-the-box default profile on Gen4. If you’re using the native Shelly integration, Matter adds nothing.

On Zigbee, Gen4 modules join a coordinator (ZHA or Zigbee2MQTT) and act as mains-powered routers. That helps build out a Zigbee mesh, but you should know what you give up, according to Shelly’s documentation:

  • Zigbee OTA updates are not supported: you have to switch the module back to Wi-Fi/Bluetooth mode to update it;
  • from firmware 1.7.0, you switch modes in the local web interface (on earlier firmware, press the button five times). So update the module over Wi-Fi before moving it to Zigbee;
  • in Zigbee2MQTT, the 2PM Gen4 shows up as two distinct devices (cover or dual switch) depending on the chosen profile, and that profile can only be changed in the Shelly web interface;
  • a model may show as “unknown” until the coordinator’s device definitions are updated.

For a first install, Wi-Fi with the native integration is still the simplest and best-documented path. Zigbee makes sense if you already have a solid Zigbee network (see which Zigbee dongle to choose and our Zigbee2MQTT tutorial) and want to keep extra clients off your Wi-Fi.

Wall boxes, the NF C 15-100 standard, and circuit protection

Room in the box. Legrand describes the 40 mm box as the standard depth and recommends the 50 mm box for electronic functions, which need more room for wiring (Legrand FAQ). A 16 mm-thick module, plus the switch mechanism and solid 1.5 mm² conductors, fills a 40 mm box fast. A 50 mm box, or one with a side compartment for a micromodule, makes all the difference. Not every wall can take one: check before you open it up. If the module won’t fit, it can go in the shutter box or in an accessible junction box. It should never end up buried in the wall without a box: France’s NF C 15-100 wiring standard requires boxes for flush-mounted circuits.

Upstream protection. The 1PM and 2PM Gen4 spec sheets call for a type B or C breaker rated 16 A maximum, with a breaking capacity of at least 6 kA. A lighting or shutter circuit built to NF C 15-100 is usually protected this way, but check the actual rating in your panel. The terminals take 0.5 to 4 mm² wire, stripped 6 to 7 mm and tightened to 0.4 Nm at most. A loose conductor in a module that runs warm is the classic failure.

The manufacturer’s warnings. The add-on interface on Gen4 modules carries high voltage whenever the module is powered. The operating range tops out at 40 °C: a south-facing shutter box in summer can get close.

The Pro range at the panel. If every shutter and lighting circuit has its own cable run back to the panel, DIN-rail Pro modules with a wired network port centralize everything without putting anything behind the switches. That makes sense in a major renovation, not a simple swap.

When to call an electrician

Get help:

  • if you can’t identify live, neutral, switched return, and up/down wires with a meter;
  • if the box has no neutral and one needs to be run;
  • if the panel has no 30 mA RCD or you don’t know the protection ratings;
  • if old wiring has no ground conductor, damaged insulation, or questionable daisy-chaining;
  • for a panel installation with Pro modules.

Always switch off the breaker for the circuit and confirm there’s no voltage before working on it. The 2PM and 1PM look alike, but their wiring diagrams differ: follow the one in the spec sheet for your exact model. On the software side, if you’re still weighing your hub options, our Home Assistant, Jeedom, or Domoticz comparison helps you decide.

Frequently asked questions

Does my wall switch still work if Wi-Fi goes down?

Yes. The wall switch is wired to the module’s input, and the module drives its relay locally. Only remote and Home Assistant control is interrupted.

Do I need a Shelly Cloud account?

No. Gen2 and newer modules are added to Home Assistant by IP address and communicate locally. The cloud is optional.

Can I use Wi-Fi and Zigbee at the same time?

Shelly’s documentation presents Zigbee and Wi-Fi/Bluetooth as two modes you switch between. Plan on one mode being active at a time, and on switching back to Wi-Fi for every update.

Key facts

10 A per channel, 16 A total
2PM Gen4
20 W minimum load without bypass
Dimmer Gen3 without neutral
37 × 42 × 16 mm (Gen4)
Module size
Type B or C breaker, 16 A max, 6 kA
Upstream protection

Our picks

Affiliate links · same price for you
Roller shutters
📦

Shelly 2PM Gen4

View on Amazon

Amazon · price and availability on the listing

Lighting with neutral
📦

Shelly 1PM Gen4

View on Amazon

Amazon · price and availability on the listing

No neutral
📦

Shelly Dimmer Gen3

View on Amazon

Amazon · price and availability on the listing

See all our recommended gear in the shop.

Tags: shellyhome assistantroller shutterslightingzigbeehome automation

Related

Comparisons

Home Assistant vs Jeedom vs Domoticz 2026: Best Self-Hosted Home Automation

Home Assistant, Jeedom or Domoticz in 2026: Matter and Thread support, Zigbee gateways, which install methods are still supported, the right hardware, and the real limits of each local home automation platform.

Read
Comparisons

Zigbee Smart Bulbs for Home Assistant: Philips Hue, IKEA, Innr, or LIDL?

Les Philips Hue Bluetooth bulbs can function without a bridge, but their limited range and specific association method make them less suitable for a robust Zigbee mesh.

Read
Comparisons

Reading your Linky meter in Home Assistant: TIC modules, ZLinky and alternatives

Read your Linky in Home Assistant: I1/I2/A terminals, historique vs standard mode, ZLinky Zigbee, ESP32 ESPHome, next-day Enedis cloud add-on and safe wiring.

Read